2012Swiss company since
5gateway models
50+drivers & protocols
100%Swiss engineering
They trust us
One gateway, every protocol
Connect, translate and supervise your whole installation on a single device.
Buildings and industrial sites run on a patchwork of protocols — KNX, BACnet, Modbus, M-Bus, MQTT, OPC UA and more, often from different vendors. The WBox brings them together on a single device: it translates and routes data between every protocol, centralises supervision, raises alarms and streams readings to the cloud — with no PC, no middleware and no vendor lock-in.
Gateway range
Five models covering all needs, from small projects to industrial deployments.
WBox Edge E413-LTE
Flagship model with built-in LTE Cat 1 modem. For remote sites without fixed connectivity.
RS-4852 ports
Ethernet2 ports
LTEBuilt-in modem
RAM4 GB
CPU4 × Cortex-A72, 1.5 GHz
RAM4 GB
Ethernet ports2 × 1 Gbps
LTECat 1 + SIM slot
RS4852 ports
WBox G110
Dual Ethernet for multi-network deployments and protocol bridging between LAN and field bus.
RS-4852 ports
Ethernet2 ports
RAM1 GB
CPU4 × Cortex-A7, 1.2 GHz
RAM1 GB
Ethernet ports2 × (1 Gbps + 100 Mbps)
RS4852 ports
WBox S485
Standard field-bus gateway. Two RS485 ports for flexible deployment.
RS-4852 ports
RAM1 GB
CPU4 × Cortex-A7, 1.2 GHz
RAM1 GB
Ethernet ports1 × 100 Mbps
RS4852 ports
WBox S485 KNX
Direct connection to the KNX TP bus via integrated port, no external KNX/IP router needed.
RS-4851 port
KNX TP1 port
RAM1 GB
CPU4 × Cortex-A7, 1.2 GHz
RAM1 GB
Ethernet ports1 × 100 Mbps
RS4851 port
KNXTP / USB / IP
WBox S103
I/O controller with digital and analog inputs/outputs + 1-Wire bus. For direct interaction with sensors and actuators.
RS-4851 port
I/OIO boards4DO · 4DI · 1AO · 1AI · One Wire
RAM1 GB
CPU4 cores @ 1.2 GHz
RAM1 GB
Ethernet ports1 × 100 Mbps
Wi-FiAccess point / Client
RS4851 port
I/O4 DI + 4 DO + 1 AI + 1 AO + 1-Wire
Not sure which model fits your project?
Our configurator walks you through a few questions, recommends the right gateway and pre-fills your cart.
Built-in features
Multi-protocol routing and serial/IP conversion built into every WBox gateway, no extra licence.
Protocol routing
Route any data between all supported protocols (KNX, BACnet, Modbus, M-Bus, MQTT…), one-way or bidirectional.
TCP ⇄ Serial
Bidirectional gateway between the IP world and the RS485 serial bus: expose your serial equipment over TCP, or operate it remotely through a virtual COM port.
Web-based configuration
Everything is configured from the browser — no extra tool or software to install. Access the gateway and set it up directly through its web interface.
Snapshot
Take a full copy of the system — locally on the gateway or to the cloud — to back up a configuration and restore or redeploy it in a few clicks.
REST API / PEERS
Our gateways expose an open API to interact with the controller over HTTP requests or WebSocket, through our peers system.
Modules
Licence-activated software extensions, deployable on any WBox gateway.
Drivers
50+ drivers to interconnect equipment, field buses and cloud services.
50+ more
KNX, BACnet and Modbus are just the start — explore every supported protocol and service.
© 2026 Weble GmbH. All rights reserved. General conditions